Fly Creek HV UL1 Bikepack Solution Dye Footprint

FLY CREEK HV UL BIKEPACK SOLUTION DYE SET UP INSTRUCTIONS:


1. Remove contents from stuff sack. Spread tent body out over your desired camp site.
2. Stake out the two cord loops at the head of the tent and the three loops at the foot.
3. Assemble the pole. Be careful to insert each pole section into the next by hand in-stead of allowing the shock cord to snap them together to ensure each pole section is fully seated.
4. Position the assembled pole on top of the tent body, matching the colors of the pole ends with the colors of the webbing on the tent body.
5. Insert the pole tips into the keyed hole on the TipLok Buckle™. (two at the head, one at the foot)
6. Attach the H Clip on the foot end of the tent body to the underside of the S Stopper on the pole.
7. Attach all plastic clips to the pole.
8. Drape the rainfly over the tent so that the door on the fly lines up with the door on the body.
9. Attach all Velcro® straps on the underside of the fly to the corresponding poles. (two at the head, one at the foot) The Velcro® straps are located beneath the guyout points and should all be properly secured to improve overall structural integrity.
10. Make sure the webbing at each buckle on the fly is completely slackened. Attach the buckles on the fly to those on the tent body.
11. Attach the two cord loops at the rear of the fly to the stakes that you used for the tent body.
12. Evenly tension the webbing on each buckle as needed to keep the rainfly taut.
13. Stake out the vestibule.
14. Stake out all guylines.

Separate 6” length pole segment included for emergency field repair. Slide repair pole over the break to act as a splint. Secure splint in place with tape.


FAST FLY SET UP INSTRUCTIONS:


If you purchase the optional Big Agnes footprint for your tent, it will enable you to pitch a Fast Fly shelter while leaving the tent body behind. The Fast Fly configuration requires the footprint, tent fly, poles and stakes.

1. Lay the footprint on the ground and stake out. Take note that the footprint is wider at the head than the foot.
2. Assemble the pole.
3. Position the assembled pole on top of the footprint, matching the colors of the pole ends with the colors of the webbing on the footprint.
4. Insert the pole tips into the grommets on the webbing.
5. Drape the rainfly over the pole structure matching the colors of the webbing on the fly with the webbing on the footprint.
6. Attach all Velcro® straps on the underside of the fly to the corresponding pole sections for best stability. (two at the head, one at the foot)
7. Make sure the webbing at each buckle on fly is completely slackened. Attach the buckles on the fly to those on the footprint.
8. Attach the two cord loops at the rear of the fly to the stakes that you used for the footprint.
9. Evenly tension the webbing on each buckle as needed to keep the rainfly taut.
10. Stake out the vestibule.
11. Stake out all guylines.


HELPFUL HINTS FOR TENT SET UP


Our tents are easy to set up, but we suggest you practice once at home before using them for the first time to avoid late night bickering with tent mates while fumbling around in the dark.
Before pitching tent, clear campsite of debris that may pierce tent floor.
We recommend staking out all corners, vestibules and guylines to increase space and ventilation. Securely staking out your tent and all guylines is crucial to maintaining the structural integrity of your tent.
Hang onto your stuff sacks or they’ll blow away and create backcountry litter.
Pull on the pole sleeve fabric when inserting poles to avoid any bunching in the material.
Push rather than pull poles through pole sleeves.

Thanks for choosing a Big Agnes tent!
Please feel free to contact us if you have any questions or comments.
support.bigagnes.com | 877.554.8975